Net2 Plus - Door control centre/controller with 2A-EV in Ku housing
Available, delivery time: Instant download
Product number:
682-531-D
Our benefits
- Door control centre for one door at a time
- Door control centres can be used together in one object
- Diagnostic LEDs
- Net2 Plus can replace a TCP/IP interface
- Net2 Plus can also be connected via RS485
- The flash memory allows simple updates
Product information "Net2 Plus - Door control centre/controller with 2A-EV in Ku housing"
About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.
The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.
A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.
Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing.
Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.
Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.
The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required.
Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.
Available downloads
-
Download "Installation tips"
Set up external system components via TCP/IP
Manufacturer information
Paxton Deutschland GmbH
Paxton Deutschland GmbH
Westhoffstr. 128
D–48159 Münster
Germany
verkauf@paxton-gmbh.de
Properties "Net2 Plus - Door control centre/controller with 2A-EV in Ku housing"
| Compatibility: | Paxton Net2 |
|---|---|
| Connections: | RJ45, RS485 |
| Operating models: | Cloud solution, Local installation |
| Power supply: | 230V AC |
Datasheets
Product dimensions
Door control centre: W116mm x H25mm x L126mm
Housing: B236mm x H80mm x L320mm
Login
There aren't any asked questions yet.
Accessories
%
Emergency battery for Net2 Controller
The 12V 7.2 AH VDS approved lead-acid backup battery is a
reliable power source designed for use in critical applications
. With its high capacity and VDS approval,
this battery ensures optimum performance and safety for various emergency power and
backup systems, including use with Paxton Net2 controllers in
plastic or steel enclosures.
- High capacity
With a capacity of 7.2 AH, this battery provides a reliable
power supply that is ideal for use in alarm systems,
monitoring systems and especially for Paxton Net2 controllers.
- VDS approval
This battery fulfils the strict requirements of the VDS (Association of
Property Insurers) and therefore guarantees the highest safety standards and quality
for use in safety-critical areas.
- Long service life
Lead-acid technology ensures a long service life and high
cycle stability, so you can rely on long-lasting and stable performance
- Robust design
The battery is robust and hard-wearing, making it ideal
for use in demanding environments. Its robust design
protects the cells from external influences and ensures safe operation.
- Easy installation
With standardised connections and a compact format, the
battery can be easily integrated and installed in various systems without
the need for special adaptations. It is optimised for both plastic
and steel housings of Net2 controllers.
- Environmentally friendly
This lead-acid battery is recyclable and thus contributes to an
environmentally conscious use by providing a sustainable solution for
emergency power supply systems.
The 12V 7.2 AH VDS approved
lead-acid backup battery is the perfect choice for anyone looking for a
reliable and powerful power source for their safety-critical
systems. It is ideal for use with Paxton Net2 controllers and
offers first-class performance and safety in a convenient format.
Go for quality and reliability with this powerful
battery!
Similar products
%
Entry - Control centre
Product information - The Entry control centre is the central interface between a door station and the door and supplies the monitors with data and power via PoE. The ports can also be used to extend the network of door stations and monitors using Entry extension switches or to connect the control centre to a Net2 system running Net2 v4.25 or higher.Installation - Entry components can be easily connected using Cat5 or standard RJ45 patch cables. Entry can also utilise an existing network infrastructure for easy installation. As power and data are supplied via PoE over the same cable, a separate power supply is not required.Operation - A visitor starts a video call via the bell button on the external door station. Access can then be granted to the visitor via the Entry Monitor with its intuitive touchscreen user interface. The indoor monitor can be used either with the handset (for private calls) or in hands-free mode.When connected to Net2, access to the building can be authorised via PIN or code entry and/or a proximity transponder.
%
Entry - Extension switch
Info - Entry is a door intercom that works both as a stand-alone system and together with the Paxton Net2 access control system, combining the intercom with the most important functions of Net2. Entry consists of 3 components that are automatically recognised during setup; the external door station, the indoor door intercom monitor and a door control unit.Entry is a plug-and-play solution that includes a range of possible door stations and is suitable for a variety of locations.The Net2 Entry control unit is the central interface between a door station and the door and supplies the monitors with data and power via PoE. The ports can also be used to extend the network of door stations and monitors using Net2 Entry extension switches or to connect the control unit to a Net2 system (running Net2 software V4.25 or higher).Installation - The Entry components can be easily connected using Cat5 or standard RJ45 patch cables. For easy installation, Entry can also utilise an existing network infrastructure. A separate power supply is not required thanks to PoE technology, as data and power are transmitted via the same cable.Operation - The visitor initiates a video call via the bell button on the door station. Access can now be granted via the internal Entry Monitor. This has an intuitive touchscreen user interface and can be used either via the handset for confidential calls or in hands-free mode.In conjunction with Net2 access control, access to the building can also be granted using a PIN code and/or proximity tag.
%
Net2 - I/O module in plastic housing
Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.
%
Net2 - I/O module with, 2A-EV in plastic housing
Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.
%
Net2 - I/O module, module only
Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.
%
Net2 - Nano door control centre/controller with 2A-EV in plastic housing
Info - Net2 is a networked PC-controlled access control system with the advantages of centralised control, event logging and flexible control of user access options. Each door control centre is part of a network. However, it can be operated independently of other components, make its own decisions and record events.The Net2 Nano control panel uses wireless technology developed by Paxton Access to connect to the central PC running the Net2 software. Net2 Nano door control units can be used in conjunction with Net2 Classic and Net2 Plus door control units and can be integrated into existing Net2 installations. This is particularly useful in places where cabling is difficult.Door control units are available as a module (without housing), in a plastic housing or together with a 2 A power supply in a plastic housing. Net2 nano door control units cannot be installed in a metal housing, as this would interfere with the wireless connection. Net2 nano should be used with the Net2 software.Installation - There is a label on the Net2 nano door control unit on which the connections for the reader, door opener, power supply, etc. are clearly indicated by colour coding. The device has a dedicated output for an electric strike (incl. integrated diode) and a voltage-free relay output for switching any electric strike, other opening drive or electronic device. Exit buttons, door contacts, tamper switches and alarm devices can be connected.The door control centres transmit the data to the PC via the Net2Air USB interface or the Net2Air Ethernet interface. Paxton Access supplies products to determine the required wireless range at a site prior to installation. The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Operation - All changes entered into the PC are transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied accordingly.
%
Net2 Plus - Door control centre/controller in Ku housing
About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required.Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.
%
Net2 Plus - Door control centre/controller with PoE+-EV in plastic housing
Info - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control over user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing.
%
Net2 Plus - Door control centre/controller with PoE+-EV in steel housing
About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required. Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.
%
Net2 Plus - Door control centre/controller, module only
About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required. Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.
%
Paxton10 - Alarm connector
About - The Paxton10 Alarm Connector is a miniature I/O adapter for the integration of fire and intruder alarm systems into a Paxton10 system. With its compact design, the discrete circuit board fits neatly into the detector housing.Installation - The alarm connector is inserted into the housing of the fire or burglar alarm system. The Alarm Connector has two inputs for monitoring and one output for arming or disarming an intruder alarm system. The connectors are powered via a Paxton10 door or video controller. Each door or video controller supports one alarm connector.
%
Paxton10 - Single-door controller, 12V 2A PSU
About – Paxton10 Door
Controllers are the building blocks of the Paxton10 system. Each one provides
control of a single door and a port to allow support up to three Paxton10
Wireless Connectors for additional functionality. A single Paxton10 system can include
up to 1000 door controllers.
The Paxton10 Door Controller is a network device that
communicates over TCP/IP and can be integrated into an existing network
infrastructure.
This controller is equipped with 4 inputs; tamper, 230v
fail, door contact, and RTE.
An intruder alarm can be integrated using the Paxton10
Alarm Connector (010-203).
Power over Ethernet (PoE) and PCB only (with or without
plastic enclosure) options also available.
Installation – The wiring label on
the Paxton10 Door Controller clearly shows colour coded connections for the
readers, power supply, lock etc. The 12v output for the lock can be used to
control any door, barrier or gate. Diagnostic LED’s indicate the status of the controller
and its inputs and outputs.
Controllers are connected directly to the network via TCP/IP. They are
automatically visible in the Paxton10 software under the devices menu.
Operation – Any changes made in
the Paxton10 software are immediately communicated to the door controller. When
a user presents their token to the reader, the control unit identifies them and
permits or denies access as appropriate.
Customers also bought
%
Net2 - Desktop reader, USB
Info - The desktop reader is set up next to the PC. It is used to read transponders into a Net2 system and to identify transponders that have been found.Installation - Simply connect the reader to a USB port. No further cabling is required. Additional workstations can also be equipped with desktop readers. Operation - An uncoded transponder is applied to the desktop reader. This creates a new user file and the transponder number is automatically entered. The user details are entered into the file and the transponder is then issued to the user.If a transponder that has already been issued is applied to the desktop reader, the corresponding user file appears.
%
Proximity reader - P75
Info - The Info-P series readers are suitable for Switch2 and Net2 systems. The readers are only supplied with a dark-coloured cover cap. Caps in other colours are available. These and replacement caps are available free of charge to registered installers of Paxton systems. The P-Series readers are available in four sizes.The majority of our Paxton readers are now equipped with Genuine HID Technology™. The readers can read HID™ 125 kHz proximity transponders when licensed with an activation card. If required, these readers can be activated for a Wiegand output via a separate activation card.Installation - The reader connection cable is connected to the door control unit according to the colour coding. Installation is simple and can be carried out accurately.Operation - A transponder is held in the area of the reading distance. The reader forwards the read information to the door control unit. If the transponder is recognised as authorised, the green LED flashes and access is granted. The red LED flashes and access is denied if the transponder is invalid.
%
Paxton - RJ45 reader connection block, 5 pieces
Info - A range of products to assist installers with the installation of Paxton Access products.This block converts the standard reader connector strips of the Swich2 and Net2 door control centres into RJ45 connections.
%
Entry - Monitor table stand
Product information - The desk stand allows the Entry monitor to be conveniently positioned on a desk or table.Assembly - The monitor can be easily attached to the stand using the fastening elements supplied with the product. The adjustable stand can be set at any angle.
%
Entry - Standard monitor with handset
Product info - Entry is a door intercom system for use as a standalone device or in conjunction with Paxton's Net2 and Paxton10 access control solutions. It consists of three components that are automatically recognised during set-up - external door station, indoor monitor and door control unit.The new Entry Standard monitor has a 4.3″ capacitive touchscreen and the same user interface as the Entry Premium monitor. With its straightforward, slim design, the monitor blends discreetly into any environment. The monitor is suitable for wall mounting or for mounting in a table stand (available separately) and is available with or without handset.Installation - The components are simply connected to each other using Cat5 or standard RJ45 patch cables. An existing network infrastructure can also be used for easy installation of Entry. An existing network infrastructure can also be used for easy installation of Entry. With PoE technology, power and data are supplied via the same cable, so no separate power supply is required.The Entry monitor - desk stand allows the Entry monitor to be conveniently positioned on a desk or table.Operation - A visitor starts a video call via the bell button on the external door station. Access can then be authorised for the visitor via the monitor with its intuitive touchscreen user interface. The monitor can be used in the interior either with a handset (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.
%
Entry - Intercom/door station stainless steel, vandal-proof, flush-mounted
Product information - Entry is a door intercom system for operation as a standalone device or in conjunction with the Net2 and Paxton10 access control solutions from Paxton. An external door station component of the Entry door intercom system. This variant of the door station can open up opportunities in locations where vandal resistance (VR) is a requirement. The VR door station has a market leading impact resistance rating of IK10 and is manufactured from marine grade stainless steel to withstand the most demanding environments.All Entry door stations are IPX5 certified, making them suitable for external use in all weather conditions.Installation - Entry components can be easily connected using Cat5 or standard RJ45 patch cables. Entry can also utilise an existing network infrastructure for easy installation. As power and data are supplied via PoE over the same cable, a separate power supply is not required.With this flush-mounted door station model, the device is flush-mounted in the wall. If there are several entrances with a door station, more than one door station can be assigned to an access control unit (ACU).A secondary IP camera can also be installed and integrated into the entry system to provide additional security for areas that are difficult to see. This offers more flexibility, as it is possible to switch back and forth between the two cameras on the Entry Monitor.Operation - A visitor starts a video call via the bell button on the external door station. Access can be authorised for the visitor via the Entry Monitor with its intuitive touchscreen user interface. The internal monitor can be used either via the handset (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.