Net2 Pro - Software

Info - The Info-P series readers are suitable for Switch2 and Net2 systems. The readers are only supplied with a dark-coloured cover cap. Caps in other colours are available. These and replacement caps are available free of charge to registered installers of Paxton systems. The P-Series readers are available in four sizes.Installation - The reader connection cable is connected to the door control unit according to the colour coding. Installation is simple and can be carried out accurately.Operation - A transponder is held in the area of the reading distance. The reader forwards the read information to the door control unit. If the transponder is recognised as authorised, the green LED flashes and access is granted. The red LED flashes and access is denied if the transponder is invalid.Our P50 Mifare readers are now equipped with Genuine HID Technology®. When licensed with an activation card, the readers can read HID 125kHz proximity transponders. If required, these readers can also be activated for a Wiegand output via a separate activation card.

Info - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control over user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing.

This layer 2/3 switch with extensive L3 functions was specially developed for applications with high data loads, such as video over IP, video streaming also in conjunction with multicast . The compact design and reduced number of ports make this switch ideal for smaller systems or as a remote unit in a larger network. With its extensive management options, can also fulfil complex network requirements. Special features for access control Component-friendly features Extra high backplane performance for smooth transmission with full port utilisation. Jumbo frames up to 9600bytes are also supported at 100MBit/s. port security through MAC address restriction. DMS DMS (Device Management System) The switch has an integrated network monitoring and control system, which gives the user a very simple overview of the entire network. This DMS system has the following features: Graphical network overview The network topology view provides a quick overview of all switches and end devices in the network, such as IP cameras or servers, with details of the IP address, device type and name. Maps and maps can be stored as background images with which the user can quickly access specific network devices even without knowledge of the IP structure. Device search This function also allows targeted access to a specific device in larger networks. Newly added devices, such as a replaced IP camera, are displayed immediately and allow the user to access immediately without knowing the IP address. Data traffic display The data traffic can be displayed graphically per port over a time axis. Error handling and security Network diagnostics between master switch and connected end devices. Protection mechanisms such as data rate limitation allow effective protection against unauthorised access. IEEE802.3ah and IEEE802.1ag provide tools for structuring networks. Technical data General properties Supply voltage 100-240VAC, 50-60Hz Power consumption Max. 25W MTBF 25°C: 595'825h 50°C: 271'556h Operating temperature 0°C to 40°C Dimensions 220 x 134 x 44mm (WxDxH) Interfaces Copper ports 10 x 10/100/1000TX, RJ45 Fibre optic ports 2 x 100/1000, SFP or 10/100/1000TX, RJ45 (Combo) We recommend the use of our barox SFPs. The compatibility of our devices with SFPs from other manufacturers is not tested by us and is not guaranteed. Console ports 1 x RS232, RJ45 Network features Backplane 20 GBit/s MAC table 32k Configuration Console, Web GUI, SNMPv1, v2c and v3 PoE management Port settings Port disable/enable. Auto-negotiation 10/100/1000Mbps. Flow control disable/enable. Data rate control on each port. Max. Framesize, Power Control Port status display Display per port: speed link status, flow control status. Auto negotiation status, trunk status. Layer3 functions IPv4 and IPv6 unicast: static routing VLAN 802.1Q Tagged based VLAN, up to 255 VLAN groups, Q-in-Q, private VLAN Link Aggregation IEEE 802.3ad LACP / Static trunk, supports 18 groups of 8-port trunks or static trunk QoS Traffic classification based, Strict priority and WRR, 4-level priority for Switching - Port number - 802.1p priority- DS/TOS field in IP Packet Security SSH, SSL, 802.1X RADIUS, port security, ACL with MAC, IP, multicast and much more. User authentication with private key Multicast IGMP v1/v2/v3 snooping, up to 1024 multicast groups, source-specific multicast, IGMP proxy Topology STP, RSTP, MSTP Standards IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000T IEEE 802.3x Flow Control and Back pressure IEEE 802.3ad Port trunk with LACP IEEE 802.1d Spanning tree protocol IEEE 802.1w Rapid spanning tree protocol IEEE 802.1s Multiple spanning tree protocol IEEE 802.1p Class ofservice IEEE 802.1Q VLAN Tagging IEEE 802.1x Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.az Energy Efficient Ethernet Types/features RY-LGS23-10G RY-19'' bracket Pair of brackets for mounting the RY-GSP23-10G in a 19" frame Included in the scope of delivery

Info - The desktop reader is set up next to the PC. It is used to read transponders into a Net2 system and to identify transponders that have been found.Installation - Simply connect the reader to a USB port. No further cabling is required. Additional workstations can also be equipped with desktop readers. Operation - An uncoded transponder is applied to the desktop reader. This creates a new user file and the transponder number is automatically entered. The user details are entered into the file and the transponder is then issued to the user.If a transponder that has already been issued is applied to the desktop reader, the corresponding user file appears.