Entry - Control centre

Info - Entry is a door intercom that works both as a stand-alone system and together with the Paxton Net2 access control system, combining the intercom with the most important functions of Net2. Entry consists of 3 components that are automatically recognised during setup; the external door station, the indoor door intercom monitor and a door control unit.Entry is a plug-and-play solution that includes a range of possible door stations and is suitable for a variety of locations.The Net2 Entry control unit is the central interface between a door station and the door and supplies the monitors with data and power via PoE. The ports can also be used to extend the network of door stations and monitors using Net2 Entry extension switches or to connect the control unit to a Net2 system (running Net2 software V4.25 or higher).Installation - The Entry components can be easily connected using Cat5 or standard RJ45 patch cables. For easy installation, Entry can also utilise an existing network infrastructure. A separate power supply is not required thanks to PoE technology, as data and power are transmitted via the same cable.Operation - The visitor initiates a video call via the bell button on the door station. Access can now be granted via the internal Entry Monitor. This has an intuitive touchscreen user interface and can be used either via the handset for confidential calls or in hands-free mode.In conjunction with Net2 access control, access to the building can also be granted using a PIN code and/or proximity tag.

Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.

Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.

Info - The Net2 I/O module has 4 inputs and 4 outputs. It is connected directly to the Ethernet (LAN/WAN) via an RJ45 connection on the circuit board. I/O modules can therefore be distributed throughout a building according to requirements. Inputs and outputs can be controlled via the "Trigger actions" function of the Net2 software. The I/O module is available as an assembly, in a plastic housing or in a plastic/metal housing with a built-in 2 A power supply.Installation - The module's connection terminals are clearly labelled. The I/O module is equipped with the same proven terminal strips as the Net2 door control centres.Operation - The parameterisation of the inputs and outputs of the I/O module is configured using the "Trigger actions" function of the Net2 software.

Info - Net2 is a networked PC-controlled access control system with the advantages of centralised control, event logging and flexible control of user access options. Each door control centre is part of a network. However, it can be operated independently of other components, make its own decisions and record events.The Net2 Nano control panel uses wireless technology developed by Paxton Access to connect to the central PC running the Net2 software. Net2 Nano door control units can be used in conjunction with Net2 Classic and Net2 Plus door control units and can be integrated into existing Net2 installations. This is particularly useful in places where cabling is difficult.Door control units are available as a module (without housing), in a plastic housing or together with a 2 A power supply in a plastic housing. Net2 nano door control units cannot be installed in a metal housing, as this would interfere with the wireless connection. Net2 nano should be used with the Net2 software.Installation - There is a label on the Net2 nano door control unit on which the connections for the reader, door opener, power supply, etc. are clearly indicated by colour coding. The device has a dedicated output for an electric strike (incl. integrated diode) and a voltage-free relay output for switching any electric strike, other opening drive or electronic device. Exit buttons, door contacts, tamper switches and alarm devices can be connected.The door control centres transmit the data to the PC via the Net2Air USB interface or the Net2Air Ethernet interface. Paxton Access supplies products to determine the required wireless range at a site prior to installation. The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Operation - All changes entered into the PC are transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied accordingly.

About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required.Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.

About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required. Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.

Info - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control over user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing.

About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required. Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.

About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required. Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.

About - The Paxton10 Alarm Connector is a miniature I/O adapter for the integration of fire and intruder alarm systems into a Paxton10 system. With its compact design, the discrete circuit board fits neatly into the detector housing.Installation - The alarm connector is inserted into the housing of the fire or burglar alarm system. The Alarm Connector has two inputs for monitoring and one output for arming or disarming an intruder alarm system. The connectors are powered via a Paxton10 door or video controller. Each door or video controller supports one alarm connector.

About –  Paxton10 Door Controllers are the building blocks of the Paxton10 system. Each one provides control of a single door and a port to allow support up to three Paxton10 Wireless Connectors for additional functionality. A single Paxton10 system can include up to 1000 door controllers. The Paxton10 Door Controller is a network device that communicates over TCP/IP and can be integrated into an existing network infrastructure. This controller is equipped with 4 inputs; tamper, 230v fail, door contact, and RTE. An intruder alarm can be integrated using the Paxton10 Alarm Connector (010-203). Power over Ethernet (PoE) and PCB only (with or without plastic enclosure) options also available. Installation – The wiring label on the Paxton10 Door Controller clearly shows colour coded connections for the readers, power supply, lock etc. The 12v output for the lock can be used to control any door, barrier or gate. Diagnostic LED’s indicate the status of the controller and its inputs and outputs. Controllers are connected directly to the network via TCP/IP. They are automatically visible in the Paxton10 software under the devices menu. Operation – Any changes made in the Paxton10 software are immediately communicated to the door controller. When a user presents their token to the reader, the control unit identifies them and permits or denies access as appropriate.