Ludwigsburg Fertility Center Dr. Ott

This layer 2/3 switch with extensive L3 functions was specially developed for applications with a high data load, such as video over IP, video streaming also in conjunction with multicast. The PoE allows IP cameras to be powered via the data cable. With the extensive management options, even complex network requirements can be fulfilled. Special features for access control Active monitoring of the components Components powered by the switch via PoE are constantly monitored. In the event of a failure, the switch restarts the controllers independently . If this is not successful, the switch sends an alarm message via SNMP. Active monitoring of the PoE power supply If, for example, too much power is required from the switch due to a defective camera, the switch sends an alarm via SNMP. Active management of the PoE power When the switch is started up, the individual PoE ports can be started up with a time delay to prevent the PoE power supply from being overloaded . Further component-friendly features Extra high backplane performance for smooth transmission with full port utilisation. Jumbo frames up to 9600 bytes are also supported at 100 Mbit/s . Port security through MAC address restriction. DMS DMS (Device Management System)The switch has an integrated network monitoring and control system, which gives the user a good overview of the entire network in a very simple way. This DMS system has the following features: Graphical network overview The network topology view provides a quick overview of all switches and end devices in the network, such as IP cameras or servers, with details of the IP address, device type and name. Maps and maps can be stored as background images, allowing the user to quickly access specific network devices even without knowledge of the IP structure, Device search This function makes it possible to access a specific device even in larger networks. Newly added devices, such as a replaced IP camera, are displayed immediately and allow the user immediate access without knowledge of the IP address. Data traffic display The data traffic can be displayed graphically per port over a time axis. Error handling and security Network diagnostics between master switch and connected end devices. Protection mechanisms such as data rate limiting allow effective protection against unwanted access. With IEEE802.3ah and IEEE802.1ag, tools are available for structuring networks. Technical data General properties Supply voltage 100-240VAC, 50-60Hz Power consumption Max. 40W (without PoE) / 255W (with PoE 185W) / 450W (with PoE 370W) MTBF 25°C: 266'508h 40°C: 158'506h Operating temperature 0°C to 40°C Dimensions 442 x 211 x 44mm (WxDxH) Interfaces Copper ports 26 x 10/100/1000TX, RJ45, 24 of which with PoE+ 802.3af/at Maximum PoE power across all ports: 185W Fibre optic ports 2 x 100/1000, SFP (Combo) We recommend the use of our barox SFPs. The compatibility of our devices with SFPs from other manufacturers is not tested or guaranteed by us. Console port RS232, RJ45 Network properties Backplane 52Gbit/s MAC table 8k Configuration Console, Web GUI, SNMPv1, v2c and v3 PoE management Port settings Port disable/enable. Auto-negotiation 10/100/1000Mbps. Flow control disable/enable. Data rate control on each port. Max. Framesize, Power Control Port status display Display per port Speed link status, flow control status. Auto negotiation status, trunk status. Layer3 functions IPv4 and IPv6 unicast: static routing VLAN 802.1Q Tagged based VLAN, up to 255 VLAN groups, Q-in-Q, private VLAN Link aggregation IEEE 802.3ad LACP / Static Trunk, supports 18 groups of 8-port trunks or static trunk QoS Traffic classification based, Strict priority and WRR, 4-level priority for switching - Port number - 802.1p priority - DS/TOS field in IP packet Security SSH v1 and v2, SSL, 802.1X RADIUS, port Security, ACL with MAC, IP, multicast and many more User authentication with private key Multicast IGMP v1/v2/v3 snooping, up to 1024 multicast groups, source-specific multicast, IGMP proxy Topology STP, RSTP, MSTP Standards IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000T IEEE 802.3x Flow Control and Back pressure IEEE 802.3ad Port trunk with LACP IEEE 802.1d Spanning tree protocol IEEE 802.1w Rapid spanning tree protocol IEEE 802.1s Multiple spanning tree protocol IEEE 802.1p Class ofservice IEEE 802.1Q VLAN tagging IEEE 802.1x Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3af/at Power over Ethernet IEEE 802.az Energy Efficient Ethernet Types/features RY-LGSP23-26/370 See separate data sheet Switch with 370W for PoE

About - Net2 Plus is a network-based access control system. Such a system offers the possibility of centralised management, event notification and flexible control of user access authorisations. Each door control centre is part of the network, but can also work independently. It makes its own decisions and saves events.The Net2 Plus door control centre is connected to the management computer with an RJ45 plug via a normal TCP/IP network. This greatly increases the flexibility of installation in buildings with LAN/WAN networks. The Net2 Plus door control centre also has an RS485 connection. This allows it to be connected to other Net2 Plus or Net2 Classic door control units via a CAT5 cable.A Net2 Plus door control unit can also act as an interface to a LAN for an RS485 connection (daisy chain) of other Net2 Plus or Net2 Classic door control units so that they no longer require a TCP/IP interface.Door control units are sold as an assembly, in a plastic housing or with a 2 A power supply in a plastic housing. Installation - There is a label on the Net2 Plus door control unit that clearly shows the colour-coded connections for reader, power supply, etc. The door control centre has a relay with potential-free contacts and can therefore control electric strikes or other opening drives. Door and tamper contacts, exit buttons and local alarm devices can also be connected.Door control centres communicate with the PC via the standard TCP/IP protocol of a LAN network. The Net2 Plus door control centre should be assigned a fixed IP address. All settings are made in the Net2 Configuration Utility.The corresponding connections are equipped with diagnostic LEDs, which are helpful for a trouble-free installation. Terminal resistors can be switched on or off as required. External terminal resistors are not required.Operation - All changes entered in the PC are immediately transmitted to the door control centre and stored there. When a user presents a transponder to a reader, the user is identified by the door control centre and access is granted or denied as appropriate.

Product info - Entry is a door intercom for use as a standalone device or in conjunction with Paxton's Net2 and Paxton10 access control solutions. The Entry Touch is a premium outdoor door station for use with the Entry door intercom system from Paxton. Featuring a high quality 7" colour touch screen with personalisation options, the Entry Touch also has induction loop connectivity to meet the needs of hard of hearing users and offers advanced sound processing for high traffic areas, making it suitable for more locations than ever before.When used with the Entry Premium Monitor, the Touch Door Station supports two-way video calling and offers the ability to leave video voicemails.All Entry door stations are IPX5 certified, making them suitable for outdoor use in all weather conditions.Installation - Entry components can be easily connected using Cat5 or standard RJ45 patch cables. Entry can also utilise an existing network infrastructure for easy installation. Since power and data are supplied via PoE over the same cable, a separate power supply is not required.In this door station model with weather protection, the device is mounted directly on the wall surface, with an additional 41 mm casing to protect the screen and keypad from rain. If there are several entrances with a door station, more than one door station can be assigned to an access control unit (ACU).A secondary IP camera can also be installed and integrated into the entry system to provide additional security for areas with poor visibility. This offers more flexibility, as it is possible to switch back and forth between the two cameras on the Entry Monitor.Operation - A visitor starts a video call via the bell button on the external door station. Access can be authorised for the visitor via the Entry Monitor. The monitor in the indoor area can be used either via the receiver (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.

Product info - Entry is a door intercom system for operation as a standalone device or in conjunction with Paxton's Net2 and Paxton10 access control solutions. It consists of three components that are automatically recognised during set-up - external door station, indoor monitor and door control unit.The premium monitor features a 7" capacitive colour touchscreen, free concierge management functions and various design options. The monitor can be wall-mounted or used as a desktop unit.When used with the Entry Touch door station, the Premium Monitor supports two-way video calls and video voicemails.Installation - Entry components can be easily connected using Cat5 or standard RJ45 patch cables. Entry can also utilise an existing network infrastructure for easy installation. Since power and data are supplied via PoE over the same cable, a separate power supply is not required.The Entry monitor - desk stand allows the Entry monitor to be conveniently positioned on a desk or table.Operation - A visitor starts a video call via the bell button on the external door station. Access can then be granted to the visitor via the Entry Monitor with its intuitive touchscreen user interface. The monitor can be used indoors with the handset (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.

Info - The Info-P series readers are suitable for Switch2 and Net2 systems. The readers are only supplied with a dark-coloured cover cap. Caps in other colours are available. These and replacement caps are available free of charge to registered installers of Paxton systems. The P-Series readers are available in four sizes.The majority of our Paxton readers are now equipped with Genuine HID Technology™. The readers can read HID™ 125 kHz proximity transponders when licensed with an activation card. If required, these readers can be activated for a Wiegand output via a separate activation card.Installation - The reader connection cable is connected to the door control unit according to the colour coding. Installation is simple and can be carried out accurately.Operation - A transponder is held in the area of the reading distance. The reader forwards the read information to the door control unit. If the transponder is recognised as authorised, the green LED flashes and access is granted. The red LED flashes and access is denied if the transponder is invalid.