IP / PoE extender via coaxial or UTP cable
Delivery time 1-2 weeks
Product number:
UP-EXT-SET
Our benefits
- IP/PoE extender for coaxial or UTP cable
- distances up to 300m
- PoE 802.3af and at
- power supply via PoE or 48-56VDC
Product information " IP / PoE extender via coaxial or UTP cable"
The extenders
of the UP-EXT-SET series transmit 10/100Mbps Ethernet and PoE/PoE+ via
coaxial cables or twisted-pair UTP cables up to a distance of 300m. The
devices are supplied and used in pairs, the UP-EXT-CAM on the
camera side, the UP-EXT-SERV on the server side. The extenders enable
the PoE supply, e.g. of a midspan, to be passed on directly via coaxial or UTP cable
. Power is supplied via PoE or via a power supply unit on the
centre side. The devices do not require any software configuration. Diagnostic LEDs
provide an overview of the operating status. The individual devices can
be mounted on a panel using a pair of supplied retaining flanges or
up to 16 devices can be mounted on 2U using the 19" subrack UP-R2, which must be ordered separately.
Further information
System notes
Connecting several
device pairs via the same UTP cable can lead to transmission problems due to crosstalk between the
different signals in the cable.
Ideally, each device connection should therefore be realised via separate cables.
If several cables have to be
strung together on a connection route, it is important to realise these transitions as technically
well as possible. This means that, ideally, professionally
assembled RJ45 plugs are used for the transitions. If this is not possible, e.g. when using
telephone cables, care must be taken to minimise unwinding the stranding of the
wire pairs. The contact between the cores of the cables to be connected
must be as galvanically good as possible.
Shielded UTP cables can cause problems due to potential equalisation currents
. We recommend not earthing the shields in the control centre, especially when several cables are brought together in a
control centre.
Technical data
General properties
|
Supply voltage |
Power supply via PoE |
|
Power consumption |
approx. 2W without PoE |
|
MTBF |
|
|
Operating temperature |
UP-EXT-CAM: -40 to +55°C |
|
Dimensions |
82 x 25 x 63mm, LxWxH, Dimensions without connector |
|
Weight |
0.14kg per device |
Interfaces
|
Copper ports |
1 x 10/100BaseT, RJ45,
Poe and PoE+ |
|
Extender ports |
The UP-EXT-SET devices
allow the connection via data cable Cat5e or better, via coaxial cable
or via twisted pair cables such as telephone cables. Accordingly, both interfaces are also available on the
extenders. The supplied BNC to two-wire terminal adapter is used for transmission via telephone cable
. |
|
Transmission cable |
Data cable Cat5e or
better, via RJ45 socket |
|
Distance specification |
The maximum transmission distance when using the cable types mentioned above is approx. 300m The maximum Data rate
is between 90MBit/s and 10MBit/s |
Network properties
|
PoE management |
|
|
Standards |
Compatible with several
network protocols including IEEE802.3, 802.3u, 802.3x |
Types/features
|
Mounting bracket |
supplied |
|
BNC to 2-wire adapter supplied |
The adapter can be used to transmit IP and PoE with a twisted-pair two-wire cable. |
|
UP-R2 |
19" subrack for max. 16
flush-mounted EXT devices, 2U |
Available downloads
Manufacturer information
barox Kommunikation GmbH
barox Kommunikation GmbH
Weiler Str. 7
D-79540 Lörrach
Germany
mail@barox.ch
Properties " IP / PoE extender via coaxial or UTP cable"
| Connections: | 1x PoE |
|---|---|
| Extender: | COAX, UTP |
| Management: | NO |
| PoE port power: | PoE (15 watts), PoE+ (30 watts) |
| Power supply: | 56V DC, PoE |
Datasheets
Login
There aren't any asked questions yet.
Zubehör
19″ 2U carrier for max. 16 UP-EXT transmitters or receivers
Product number: UP-EXT-R2
Barox
19″ 2U carrier for max. 16 UP-EXT transmitters or receivers
The Barox 19-inch rack (2U) was specially developed for mounting up to 16 flush-mounted
transmitters or receivers. It offers a space-saving,
clear and professional solution for installation in standardised
19″ racks and is ideal for demanding video, network and
surveillance systems.
Features:
19″ rack mounting, 2
height units (2U)
Space for up to 16
UP-EXT transmitters or receivers
Robust
metal design for durable, professional use
Clean and
structured cabling possible
Simple
integration into existing rack systems
Similar products
19" subrack for LO-9500 media converter
Product number: LO-9500-R2
The LO-9500-R2
is a 19" subrack for holding media converters of the types
LO-9500-xy. Up to 14 media converters can be mounted in the subrack
. The redundant power supply ensures high availability
. The media converters are easy to install. The LO-9500-R2
is supplied with all the necessary mounting accessories.
Technical specifications
General properties
Supply voltage
Two redundant
power supply units included in the scope of delivery
2 x 110 - 230VAC
50-60Hz
Power consumption
Max. 50W at full
Equipped with 14 media converters
MTBF
Operating temperature
-20°C to +50°C
Dimensions
230 x 490 x 90mm (LxWxH)
19", 2U
Weight
4 kg
Types/features
LO-9500-S
Incl. accessories:
2 power cables
14 slide-in holders for media converters LO-9500-xy
Blanking plates, 3x4 slots and 2 x 1 slot
19" subrack for PD-VDSL
Product number: PD-R2
The PD-R2 is a 2U high 19" housing
with 17 slots. The enclosure provides an economical solution for low density VDSL2
LAN Extender installations where no
management functions are required. Each 100M VDSL2 LAN Extender can be used as a
standalone device or installed in the PD-R2 chassis. An AC power supply is built into the
subrack. The built-in fan ensures
that the temperatures in the rack remain within the permissible operating range
.
Technical data
General properties
Supply voltage
230VAC, IEC plug
Power consumption
Depending on the
assignment with VDSL modems
Base load: 10W
Per modem: 4.5W
Maximum power consumption with 17 modems: 90W
MTBF
Operating temperature
0°C ... 50°C
Power loss
307BTU/h, at maximum occupancy
Dimensions
199mm x 476mm x 88mm,
(LxWxH)
Weight
Gross weight: 6.2kg
Net weight: 5.2kg
Industrial managed media converter with PoE++ for 2 x 10/100/1000BaseTX to SFP
Product number: PD-BTPMC102M-GE
This industrial media converter with management was
specially developed for applications with high data loads, such as video over IP or video
streaming. The compact design, wide temperature range and
high flexibility make this media converter ideal for remote
locations. The media converter has an optical SFP port with 100/1000FX and
two copper ports with 10/100/1000TX, which supports PoE 802.3af/at/bt up to 90W per port and
120W. The management functions allow the PoE
to be controlled, including monitoring of the connected PDs. The cables connected to
can also be monitored remotely. The media converter can be easily mounted on a top-hat rail
using the supplied
mounting accessories.
Technical data
General properties
Supply voltage
2 x 48-56VDC
Power consumption
Max. 4W, without PoE
MTBF
Operating temperature
-40°C to +75°C
Dimensions
105 x 38 x 84 (HxWxL),
all dimensions without connector
Weight
Net 0.45 kg
Interfaces
Copper ports
2 x 10/100/1000TX with
PoE++
Per port max. 90W
Total over both ports 120W
Fibre optic ports
1 x 100/1000FX SFP
We recommend the use of our barox SFPs. The
compatibility of our devices with SFPs from other manufacturers is not
tested or guaranteed by us.
Network features
Management
Lite Management
User Management
LAN settings
Relay alarm settings
PoE Settings
User Configuration
Path GUI
DIP Switches
PoE Management
Device alive check
PoE power control
PoE status
PoE Configuration
PoE Scheduling
PoE status display
Link speed per TX port, link speed SFP port, PoE output per port, data
transmission
Security
FCC Class A, CE
Types/features
PD-BTPMC102-GE
Without SFP
Without power supply
PoE, PoE+ and PoE++ up to 90W per port
Total PoE power over both ports 120W
Mounting accessories
Bracket for top-hat rail mounting
Industrial media converter for 10/100/1000BaseTX and SFP
Product number: PC-MC101-GE
This industrial media converter was specially developed for
applications with high data loads, such as video over IP and video streaming.
The compact design, wide temperature range and high flexibility
make this media converter ideal for remote locations. Thanks to the
use of SFPs with 100 or 1,000 MBit/s, the PC-MC101-GE can be connected to
practically all common central switches. Thanks to the supplied
mounting accessories, the media converter can be easily mounted on a top-hat rail or
on a wall.
Further information
System notesThis media converter cannot be operated in
combination with the VDSL-SFPs of the PD-VDSL-SFP series.
Technical data
General properties
Supply voltage
12-56VDC, screw terminal
Without power supply unit, must be ordered separately
Power consumption
2W
MTBF
Operating temperature
-40°C to +75°C
Dimensions
59 x 36 x 50mm (WxHxD)
Weight
0.1 kg
Test standards
EMC: CE, FCC, EN 55032/24
EMI: CISPR 32, FCC Part 15B Class A
EMSiEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV
IEC
61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC
61000-4-5 Surge: Power: 2KV; Signal: 2KV
VibrationeN 60068-2-6
Shock: EN 60068-2-27
Free Fall: EN 60068-2-32
Interfaces
Copper ports
1x10/100/1000BaseTX, RJ45
Auto negotiation
Auto MDI/MDI-X
Full/half duplex
Fibre optic ports
1 x 100/1000 SFP, LC connector
Data rate of the SFP must be set via dipswitch.
We recommend the use of our barox SFPs. The
compatibility of our devices with SFPs from other manufacturers is not
tested by us and is not guaranteed.
Network features
PoE management
Standards
IEEE 802.3 10Base-T
Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
Types/features
PC-MC101-GE
For SFP slot
LC connector
Optical data dependent on SFP
Incl. mounting accessories, without SFP, without power supply
Mounting accessories
Supplied mounting accessories for wall and
DIN rail mounting
Industrial media converter for 10/100/1000BaseTX and SFP
Product number: PC-PMC101-GME
This industrial media converter was
specially developed for applications with high data loads, such as video over IP. The
very compact design, the wide temperature range and the high flexibility
make this media converter ideal for remote locations. The
media converter has a copper port with 10/100/1000TX, which supports PoE 802.3af/at up to
30W. By using SFPs with 100 or 1,000 MBit/s,
the PC-PMC101-GME can be connected to practically all common central switches.
The supplied mounting accessories make it easy to mount the media converter
on a top-hat rail or on a wall.
Further information
Special features
LFP (Link Fault Pass
Through) can be switched on and off using a dip switch.
For stable use of this function, a suitable media converter from the PC series
must also be used on the
opposite side.
System notesThis media converter
cannot be operated in combination with the VDSL-SFPs of the PD-VDSL-SFP series
.
Technical data
General properties
Supply voltage
48-56VDC, screw terminal
Without power supply unit, must be ordered separately
Power consumption
2W, without PoE
MTBF
Operating temperature
-40°C to +75°C
Dimensions
59 x 36 x 50mm (WxHxD)
Weight
0.1 kg
Test standards
EMC: CE, FCC, EN 55032/24
EMI: CISPR 32, FCC Part 15B Class A
EMSiEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV
IEC
61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC
61000-4-5 Surge: Power: 2KV; Signal: 2KV
VibrationeN 60068-2-6
Shock: EN 60068-2-27
Free Fall: EN 60068-2-32
Interfaces
Copper ports
1x10/100/1000BaseTX, RJ45, PoE+
Auto negotiation
Auto MDI/MDI-X
Full/half duplex
Fibre optic ports
1 x 100/1000 SFP, LC connector Simplex or duplex
depending on the SFP
Data rate of the SFP must be set via dipswitch
We recommend the use of our barox SFPs. The
compatibility of our devices with SFPs from other manufacturers is not
checked by us and is not guaranteed.
Network features
PoE management
Standards
IEEE 802.3 10Base-T
Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af for POE
IEEE 802.3at for POE+
Types/features
PC-PMC101-GME
For SFP slot
LC connector
Optical data dependent on SFP
Incl. mounting accessories, without SFP, without power supply
Mounting accessories
Supplied mounting accessories for wall and
DIN rail mounting
Industrial media converter with PoE++ for 10/100/1000BaseTX to SFP
Product number: PC-BTPMC101-10GE
This industrial media converter
was specially developed for applications with high data loads, such as video over IP or video
streaming. The high possible PoE power of 90W makes
this media converter suitable for components with high power requirements. The compact
design, wide temperature range and high flexibility make this
media converter ideal for remote locations. The media converter has a
optical SFP port and a copper port with 1G/10GTX, which supports PoE 802.3af/at/bt up to
90W. With the supplied mounting accessories, the
media converter can be easily mounted on a top-hat rail or on a wall.
Further information
Special features
LFP (Link Fault Pass
Through) can be switched on and off using a dip switch.
For stable use of this function, a suitable media converter from the PC series must also be used on the
opposite side
.
Technical data
General properties
Supply voltage
12-56VDC without PoE
48-56VDC with PoE
52-56VDC with PoE++ (from 30W)
Redundant power supply possible
Power consumption
Max. 4W, without PoE
MTBF
Operating temperature
-40°C to +75°C
Dimensions
104 x 32 x 82mm (HxWxL),
all dimensions without connector
Interfaces
Copper ports
1 x 1G/10G TX with
PoE++, RJ45
PoE according to IEEE802.3af, at and bt, max. 90W
Distance specification
Copper port
Data rate 1G: max. 100m, cable min. Cat5 or better
Data rate 10G: max. 50m, cable min. Cat6a or better
Fibre optic port
Depending on SFP
Fibre optic ports
1 x 1G/10G BaseFX with
SFP/SFP+
LC duplex or simplex depending on SFP
We recommend the use of our barox SFPs. The
compatibility of our devices with SFPs from other manufacturers is not
tested or guaranteed by us.
Uplink ports
1 x 1G/10G SFP/SFP+
Network features
PoE management
Security
FCC Class A, CE
Standards
802.3, 10Base-T Ethernet
802.3u, 100BaseTX and 100BaseFX Fast Ethernet
802.3ab 1000BaseTX, Gigabit Ethernet
EN55022/24, ITE equipment
EN60950-1, Safety
EN50155 / EN60068-2-6, Vibration
EN50155 / EN60068-2-27, Shock
EN50155 / EN600-2-32 Free fall
IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV
IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV
Types/features
PC-BTPMC101-10GE
Without SFP
Without power supply
PoE, PoE+ and PoE++ up to 90W
Mounting accessories incl.
Industrial media converter with PoE++ for 10/100/1000BaseTX to SFP
Product number: PC-BTPMC101-GE
This industrial media converter
was specially developed for applications with high data loads, such as video over IP or video
streaming. The high possible PoE power of 90W makes
this media converter suitable for components with high power requirements. The compact
design, wide temperature range and high flexibility make this
media converter ideal for remote locations. The media converter has a
optical SFP port and a copper port with 10/100/1000TX, which supports PoE
802.3af/at/bt up to 90W. The supplied mounting accessories allow
the media converter to be easily mounted on a top-hat rail or on a wall
.
Further information
Special features
LFP (Link Fault Pass
Through) can be switched on and off using a dip switch.
For stable use of this function, a suitable media converter from the PC series
must also be used on the
opposite side.
Technical data
General properties
Supply voltage
12-56VDC without PoE
48-56VDC with PoE
52-56VDC with PoE++ (from 30W)
Redundant power supply possible
Power consumption
Max. 4W, without PoE
MTBF
Operating temperature
-40°C to +75°C
Dimensions
104 x 32 x 82mm (HxWxL),
all dimensions without connector
Interfaces
Copper ports
1 x 10/100/1000TX
with PoE++, RJ45
PoE according to IEEE802.3af, at and bt, max. 90W
Fibre optic ports
1 x 100/1000BaseFX with
SFP
LC duplex or simplex depending on SFP
We recommend the use of our barox SFPs. The
compatibility of our devices with SFPs from other manufacturers is not
tested or guaranteed by us.
Uplink ports
1 x 100/1000SFP
Network features
PoE management
Security
FCC Class A, CE
Standards
802.3, 10Base-T Ethernet
802.3u, 100BaseTX and 100BaseFX Fast Ethernet
802.3ab 1000BaseTX, Gigabit Ethernet
EN55022/24, ITE equipment
EN60950-1, Safety
EN50155 / EN60068-2-6, Vibration
EN50155 / EN60068-2-27, Shock
EN50155 / EN600-2-32 Free fall
IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV
IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV
Types/features
PC-BTPMC101-GE
Without SFP
Without power supply
PoE, PoE+ and PoE++ up to 90W
Mounting accessories incl.
Industrial media converter with PoE++ for 10/100/1000BaseTX to SFP
Product number: PC-HPMC101-GE
This
industrial media converter was specially developed for applications with high data loads,
such as video over IP or video streaming. The compact design, the
wide temperature range and the high flexibility make this
media converter ideal for remote locations. The media converter has a
optical SFP port and a copper port with 10/100/1000TX, which supports PoE 802.3af/at
up to 60W. With the supplied mounting accessories, the
media converter can be easily mounted on a top-hat rail or on a wall.
Technical specifications
General properties
Supply voltage
12-56VDC
without PoE
48-56VDC with PoE
Power consumption
Max. 4W, without PoE
MTBF
Operating temperature
-40°C to +75°C
Dimensions
104 x 32 x 82mm (HxWxL), all dimensions without connector
Interfaces
Copper ports
PC-PMC101-GE: 1 x 10/100/1000TX with PoE+
PC-HPMC101-GE: 1 x 10/100/1000TX with PoE++
Fibre optic ports
Connectors:
Copper: RJ45, fibre optic, LC duplex or simplex depending on SFP
We
recommend the use of our barox SFPs. The compatibility of our
devices with SFPs from other manufacturers is not tested by us and is not
guaranteed.
Uplink ports
1 x 100/1000SFP
Network features
PoE management
Security
FCC Class A, CE
Standards
802.3, 10Base-T Ethernet
802.3u, 100BaseTX and 100BaseFX Fast Ethernet
802.3ab 1000BaseTX, Gigabit Ethernet
EN55032/24, ITE Equipment
EN60950-1, Safety
EN50155 / EN60068-2-6, Vibration
EN50155 / EN60068-2-27, Shock
EN50155 / EN600-2-32 Free fall
Types/features
PC-HPMC101-GE
Without SFP
Without power supply
PoE, PoE+ and PoE++ up to 60W
PC-PMC101-GE, see separate data sheet
Without SFP
Without power supply
PoE and PoE+ up to 30W
Mounting accessories
Industrial PoE splitter
Product number: VI-22301
This industrial PoE splitter allows a separate DC voltage of 12 or 24VDC
to be provided in addition to a
IP data interface with PoE+. For example, in addition to a PoE-powered IP camera
, a separate light source or a separate heater can also be supplied.
The small dimensions and wide operating temperature range
make the device particularly suitable for installation in outdoor locations.
Technical specifications
General properties
Supply voltage
PoE+ / PoE++ (PD), max. 60W
Power consumption
Max. 60W
MTBF
Operating temperature
-40° to +75°C
Dimensions
74 x 54 x 35mm
(LxWxH)
Weight
0.15 kg
Interfaces
Copper ports
1 x 10/100/1000TX,
RJ45, Data & PoE IN (PD), max. 60W
1 x 10/100/1000TX, RJ45, Data & PoE OUT (PS), max. 60W
Network features
PoE management
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3af for POE
IEEE 802.3at for POE+
Industrial PoE voltage converter 12VDC to 48-55VDC
Product number: PS-DIN-DC12/48/480
This industrial voltage converter increases an
input voltage of 9-36VDC to a voltage of
48-55VDC suitable for PoE and PoE+. This allows, for example, PoE injectors or media converters to be supplied at
locations where only voltages between 9-36VDC are available.
The voltage converter is suitable for wall or top-hat rail mounting.
Its small dimensions and wide operating temperature range make
it particularly suitable for outdoor use.
Technical specifications
General properties
Supply voltage
9-36VDC, screw terminals
Power consumption
Depending on the
supplied sink
Max. 480W
MTBF
Operating temperature
-40° to +75°C
Dimensions
38 x 95 x 75mm (WxHxD)
Weight
0.45kg
Test standards
Safety:
CE EN55035/EN61000-6-2
IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT)
IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8
(Magnetic Field)
Vibration: EN 60068-2-6
Shock: EN 60068-2-27
Free Fall: EN 60068-2-32
Network features
PoE management
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af for POE
IEEE 802.3at for POE+
Types/features
PS-DIN-DC12/48/480
Mounting accessories
Supplied
Mounting accessories for wall and top-hat rail mounting
Industrial PoE voltage converter 24VDC to 48-55VDC
Product number: PS-DIN-DC24/48/72
This industrial voltage converter increases an
input voltage of 24VDC to a voltage of
48-55VDC suitable for PoE and PoE+. This allows, for example, PoE injectors or media converters to be supplied at
locations where only 24VDC is available. The voltage converter is
suitable for wall or top-hat rail mounting. Thanks to its small
dimensions and wide operating temperature range, it is particularly suitable for
outdoor use.
Technical specifications
General properties
Supply voltage
24-56VDC, screw terminals
Power consumption
Depending on the
supplied sink
Max. 72W
MTBF
Operating temperature
-40° to +75°C
Dimensions
59 x 36 x 50mm (WxHxD)
Weight
0.1 kg
Test standards
Safety: EN60950-1
Vibration: EN 60068-2-6
Shock: EN 60068-2-27
Free Fall: EN 60068-2-32
Network features
PoE management
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af for POE
IEEE 802.3at for POE+
Types/features
PS-DIN-DC24/48/72
Mounting accessories
Supplied
Mounting accessories for wall and top-hat rail mounting
IP / PoE repeater via UTP cable (twisted pair cable)
Product number: VI-3002
The VI-3002
is a 10/100Mbps Ethernet and PoE/PoE+/PoE++ repeater. The repeater
makes it possible to connect two or more UTP Cat5/6 cable runs together
and thus multiply the cable distance. The devices do not require any
software configuration. Diagnostic LEDs provide an overview of the operating status.
Thanks to their small dimensions, the repeaters can also be installed in very tight
spaces.
Technical data
General properties
Supply voltage
The VI-3002 is powered by
the PoE on the line.
POE operation means that no separate power supply is required,
no separate power supply is possible.
Power consumption
1W
MTBF
Operating temperature
-10°C ... +70°C
Dimensions
23 x 25 x 69mm
Interfaces
Copper Ports
2 x 10/100BaseT, RJ45, PoE, PoE+ and PoE++
Transmission cable
Ideal type: Cat5e and
better
Distance specification
The VI-3002 repeater
can transmit over 100m of cable on both sides. By stringing
several repeaters together, longer distances can also be covered. Please note
that the PoE power decreases due to the voltage drop in the cable and the repeaters'
own power consumption.
Maximum number of repeaters, guide values:
PoE power
Distance
Number VI-3002
60W
130m
1
25W
300m
2
5W
500m
4
Types/features
VI-3002
Customers also bought
Entry - Touch panel, surface mounting
Product number: 337-620-D
Product info - Entry is a door intercom for use as a standalone device or in conjunction with Paxton's Net2 and Paxton10 access control solutions. The Entry Touch is a premium outdoor door station for use with Paxton's Entry door intercom system. Featuring a high quality 7" colour touch screen with personalisation options, the Entry Touch also has induction loop connectivity to meet the needs of hard of hearing users and offers advanced sound processing for high traffic areas, making it suitable for more locations than ever before.When used with the Entry Premium Monitor, the Touch Door Station supports two-way video calling and offers the ability to leave video voicemails.All Entry door stations are IPX5 certified, making them suitable for outdoor use in all weather conditions.Installation - Entry components can be easily connected using Cat5 or standard RJ45 patch cables. Entry can also utilise an existing network infrastructure for easy installation. Since power and data are supplied via PoE over the same cable, a separate power supply is not required.In this door station model with weather protection, the device is mounted directly on the wall surface, with an additional 41 mm casing to protect the screen and keypad from rain. If there are several entrances with a door station, more than one door station can be assigned to an access control unit (ACU).A secondary IP camera can also be installed and integrated into the entry system to provide additional security for areas with poor visibility. This offers more flexibility, as it is possible to switch back and forth between the two cameras on the Entry Monitor.Operation - A visitor starts a video call via the bell button on the external door station. Access can be authorised for the visitor via the Entry Monitor. The monitor in the indoor area can be used either via the receiver (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.
Compact - Relay module, 5 pieces
Product number: 325-010-D
Info - Compact systems use a 12 V DC switching voltage as the output for a lock. This is not suitable for situations where voltage-free contacts are required to control external devices, such as shutters or 24 V locks. The control output module of the compact system is designed to be connected via this output (green/yellow wires) and to provide switched (NO/NC) de-energised contacts.Installation - The connections are colour coded to show the connections for the compact system. Simply carry out the wiring according to the label on the module.Operation - The control output can be used for switching a maximum of 40 volts DC / AC at 4 A.
Entry - Standard monitor
Product number: 337-280-D
Product info - Entry is a door intercom system for use as a standalone device or in conjunction with Paxton's Net2 and Paxton10 access control solutions. It consists of three components that are automatically recognised during set-up - external door station, indoor monitor and door control unit.The new Entry Standard monitor has a 4.3″ capacitive touchscreen and the same user interface as the Entry Premium monitor. With its straightforward, slim design, the monitor blends discreetly into any environment. The monitor is suitable for wall mounting or for mounting in a table stand (available separately) and is available with or without handset.Installation - The components are simply connected to each other using Cat5 or standard RJ45 patch cables. An existing network infrastructure can also be used for easy installation of Entry. An existing network infrastructure can also be used for easy installation of Entry. With PoE technology, power and data are supplied via the same cable, so no separate power supply is required.The Entry monitor - desk stand allows the Entry monitor to be conveniently positioned on a desk or table.Operation - A visitor starts a video call via the bell button on the external door station. Access can then be authorised for the visitor via the monitor with its intuitive touchscreen user interface. The monitor can be used in the interior either with a handset (for private calls) or in hands-free mode.When connected to Net2, access to the building is authorised by entering a PIN or code and/or using a proximity transponder. When connected to Paxton10, access to the building is authorised via Bluetooth® smart credentials, PIN or code entry and/or with a proximity transponder.
Proximity reader - P75, with connection terminals
Product number: 373-120-D
Info - P-series readers are suitable for Switch2 and Net2 systems. The readers are supplied with a light and dark-coloured cover cap. Cover caps in other colours are available. These as well as replacement caps are available free of charge for registered installers of Paxton systems. The P-series readers are available in four sizes.The majority of our Paxton readers are now equipped with Genuine HID Technology™. The readers can read HID™ 125 kHz proximity transponders when licensed with an activation card. If required, these readers can be activated for a Wiegand output via a separate activation card.Installation - The reader connection cable is connected to the door control unit according to the colour coding. Installation is simple and can be carried out accurately.Operation - A transponder is held in the area of the reading distance. The reader forwards the read information to the door control unit. If the transponder is recognised as authorised, the green LED flashes and access is granted. The red LED flashes and access is denied if the transponder is invalid.
19″ 2U carrier for max. 16 UP-EXT transmitters or receivers
Product number: UP-EXT-R2
Barox
19″ 2U carrier for max. 16 UP-EXT transmitters or receivers
The Barox 19-inch rack (2U) was specially developed for mounting up to 16 flush-mounted
transmitters or receivers. It offers a space-saving,
clear and professional solution for installation in standardised
19″ racks and is ideal for demanding video, network and
surveillance systems.
Features:
19″ rack mounting, 2
height units (2U)
Space for up to 16
UP-EXT transmitters or receivers
Robust
metal design for durable, professional use
Clean and
structured cabling possible
Simple
integration into existing rack systems